PARAMETER VERSION = 2.1.0


 PORT Clk = Clk_x, DIR = I, SIGIS = CLK, CLK_FREQ = 100000000
 PORT sw = sw_x, DIR = I, VEC = [7:0]
 PORT btn = btn_x, DIR = I, VEC = [4:0]
 PORT Led = led_x, DIR = O, VEC = [7:0]
 PORT seg = seg_x, DIR = O, VEC = [7:0]
 PORT an = an_x, DIR = O, VEC = [3:0]
 PORT RsRx = Rx, DIR = I
 PORT RsTx = Tx, DIR = O
 PORT T200kHz = T200kHz_x, DIR = O


BEGIN proc_sys_reset
 PARAMETER INSTANCE = reset_0
 PARAMETER HW_VER = 3.00.a
 PORT Interconnect_aresetn = reset_0_Interconnect_aresetn
 PORT Bus_Struct_Reset = reset_0_Bus_Struct_Reset
 PORT Peripheral_Reset = reset_0_Peripheral_Reset
 PORT MB_Reset = reset_0_MB_Reset
 PORT MB_Debug_Sys_Rst = debug_module_0_Debug_SYS_Rst
 PORT Dcm_locked = net_vcc
 PORT Slowest_sync_clk = Clk_x
END

BEGIN microblaze
 PARAMETER INSTANCE = cpu
 PARAMETER HW_VER = 8.50.b
 PARAMETER C_DEBUG_ENABLED = 1
 PARAMETER C_INTERCONNECT = 2
 BUS_INTERFACE M_AXI_DP = axi_interconnect_0
 BUS_INTERFACE DLMB = dlmb
 BUS_INTERFACE ILMB = ilmb
 BUS_INTERFACE DEBUG = debug_module_0_MBDEBUG_0
 PORT MB_RESET = reset_0_MB_Reset
END

BEGIN lmb_v10
 PARAMETER INSTANCE = ilmb
 PARAMETER HW_VER = 2.00.b
 PORT LMB_Clk = Clk_x
 PORT SYS_Rst = reset_0_Bus_Struct_Reset
END

BEGIN lmb_v10
 PARAMETER INSTANCE = dlmb
 PARAMETER HW_VER = 2.00.b
 PORT LMB_Clk = Clk_x
 PORT SYS_Rst = reset_0_Bus_Struct_Reset
END

BEGIN iomodule
 PARAMETER INSTANCE = iomodul
 PARAMETER HW_VER = 1.03.a
 PARAMETER C_BASEADDR = 0x00040000
 PARAMETER C_HIGHADDR = 0x0004FFFF
 PARAMETER C_USE_UART_RX = 1
 PARAMETER C_USE_UART_TX = 1
 PARAMETER C_USE_GPI1 = 1
 PARAMETER C_GPI1_SIZE = 8
 PARAMETER C_USE_GPI2 = 1
 PARAMETER C_GPI2_SIZE = 5
 PARAMETER C_USE_GPO1 = 1
 PARAMETER C_GPO1_SIZE = 8
 PARAMETER C_GPO1_INIT = 0x00000000
 PARAMETER C_USE_GPO2 = 1
 PARAMETER C_GPO2_SIZE = 8
 PARAMETER C_USE_PIT1 = 1
 PARAMETER C_PIT1_INTERRUPT = 1
 PARAMETER C_USE_FIT1 = 1
 PARAMETER C_FIT1_No_CLOCKS = 100
 PARAMETER C_FIT1_INTERRUPT = 1
 PARAMETER C_USE_FIT2 = 1
 PARAMETER C_FIT2_No_CLOCKS = 10000
 PARAMETER C_FIT2_INTERRUPT = 1
 PARAMETER C_USE_FIT3 = 1
 PARAMETER C_FIT3_No_CLOCKS = 100000000
 PARAMETER C_FIT3_INTERRUPT = 1
 PARAMETER C_USE_GPO3 = 1
 PARAMETER C_GPO3_SIZE = 4
 PARAMETER C_PIT1_PRESCALER = 1
 BUS_INTERFACE SLMB = dlmb
 PORT CLK = Clk_x
 PORT Rst = reset_0_Peripheral_Reset
 PORT GPI1 = sw_x
 PORT GPI2 = btn_x
 PORT GPO1 = led_x
 PORT GPO2 = seg_x
 PORT GPO3 = an_x
 PORT UART_Rx = Rx
 PORT UART_Tx = Tx
 PORT FIT1_Toggle = T200kHz_x
END

BEGIN mdm
 PARAMETER INSTANCE = debug_module_0
 PARAMETER HW_VER = 2.10.a
 PARAMETER C_INTERCONNECT = 2
 PARAMETER C_USE_BSCAN = 1
 PARAMETER C_USE_UART = 1
 PARAMETER C_BASEADDR = 0x41400000
 PARAMETER C_HIGHADDR = 0x4140ffff
 BUS_INTERFACE S_AXI = axi_interconnect_0
 BUS_INTERFACE MBDEBUG_0 = debug_module_0_MBDEBUG_0
 PORT Debug_SYS_Rst = debug_module_0_Debug_SYS_Rst
 PORT S_AXI_ACLK = Clk_x
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = dbram_cntlr
 PARAMETER HW_VER = 3.10.c
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x00001fff
 BUS_INTERFACE SLMB = dlmb
 BUS_INTERFACE BRAM_PORT = bram_cntlr_d_BRAM_PORT
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = ibram_cntlr
 PARAMETER HW_VER = 3.10.c
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x00001fff
 BUS_INTERFACE SLMB = ilmb
 BUS_INTERFACE BRAM_PORT = bram_cntlr_0_BRAM_PORT
END

BEGIN bram_block
 PARAMETER INSTANCE = bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = bram_cntlr_0_BRAM_PORT
 BUS_INTERFACE PORTB = bram_cntlr_d_BRAM_PORT
END

BEGIN axi_interconnect
 PARAMETER INSTANCE = axi_interconnect_0
 PARAMETER HW_VER = 1.06.a
 PARAMETER C_INTERCONNECT_CONNECTIVITY_MODE = 0
 PARAMETER C_RANGE_CHECK = 0
 PORT INTERCONNECT_ACLK = Clk_x
 PORT INTERCONNECT_ARESETN = reset_0_Interconnect_aresetn
END