# ##############################################################################
# mhs-Datei zum einführenden Beispiel zum Script "Softprozessor-Praktikum"
# Author: G. Kemnitz
# Wed Sep 17 16:42:28 2014
# Target Board:  nexys3
# Family:    spartan6
# Device:    xc6slx16
# Package:   csg324
# Speed Grade:  -2
# ##############################################################################
 PARAMETER VERSION = 2.1.0

 PORT CLK = CLK, DIR = I, SIGIS = CLK, CLK_FREQ = 100000000
 PORT Led = Led, DIR = O, VEC = [7:0]

BEGIN lmb_v10
 PARAMETER INSTANCE = mb0_ilmb
 PARAMETER HW_VER = 2.00.b
 PORT SYS_RST = Rst
 PORT LMB_CLK = CLK
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = mb0_ibram_ctrl
 PARAMETER HW_VER = 3.10.c
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x00001fff
 BUS_INTERFACE SLMB = mb0_ilmb
 BUS_INTERFACE BRAM_PORT = BRI
END

BEGIN lmb_v10
 PARAMETER INSTANCE = mb0_dlmb
 PARAMETER HW_VER = 2.00.b
 PORT SYS_RST = Rst
 PORT LMB_CLK = CLK
END

BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = mb0_dbram_ctrl
 PARAMETER HW_VER = 3.10.c
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x00001fff
 BUS_INTERFACE SLMB = mb0_dlmb
 BUS_INTERFACE BRAM_PORT = BRD
END

BEGIN bram_block
 PARAMETER INSTANCE = mb0_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = BRI
 BUS_INTERFACE PORTB = BRD
END

BEGIN microblaze
 PARAMETER INSTANCE = microblaze_0
 PARAMETER HW_VER = 8.50.b
 PARAMETER C_INTERCONNECT = 2
 PARAMETER C_USE_BARREL = 1
 PARAMETER C_USE_FPU = 0
 PARAMETER C_DEBUG_ENABLED = 1
 PARAMETER C_USE_ICACHE = 0
 PARAMETER C_USE_DCACHE = 0
 BUS_INTERFACE ILMB = mb0_ilmb
 BUS_INTERFACE DLMB = mb0_dlmb
 BUS_INTERFACE M_AXI_DP = mb0_axi
 BUS_INTERFACE DEBUG = dbg
 PORT MB_RESET = Debug_Rst
 PORT CLK = CLK
END

BEGIN axi_interconnect
 PARAMETER INSTANCE = mb0_axi
 PARAMETER HW_VER = 1.06.a
 PARAMETER C_INTERCONNECT_CONNECTIVITY_MODE = 0
 PORT INTERCONNECT_ARESETN = NotRst
 PORT INTERCONNECT_ACLK = CLK
END

BEGIN mdm
 PARAMETER INSTANCE = debug_module
 PARAMETER HW_VER = 2.10.a
 PARAMETER C_INTERCONNECT = 2
 PARAMETER C_USE_UART = 1
 PARAMETER C_BASEADDR = 0x41400000
 PARAMETER C_HIGHADDR = 0x4140ffff
 BUS_INTERFACE MBDEBUG_0 = dbg
 BUS_INTERFACE S_AXI = mb0_axi
 PORT Debug_SYS_Rst = Debug_Rst
 PORT S_AXI_ACLK = CLK
END

BEGIN axi_gpio
 PARAMETER INSTANCE = axi_gpio_0
 PARAMETER HW_VER = 1.01.b
 PARAMETER C_BASEADDR = 0x40000000
 PARAMETER C_HIGHADDR = 0x4000ffff
 PARAMETER C_GPIO_WIDTH = 8
 BUS_INTERFACE S_AXI = mb0_axi
 PORT S_AXI_ACLK = CLK
 PORT GPIO_IO_O = Led
END

BEGIN proc_sys_reset
 PARAMETER INSTANCE = reset_0
 PARAMETER HW_VER = 3.00.a
 PORT Dcm_locked = net_vcc
 PORT Bus_Struct_Reset = Rst
 PORT Interconnect_aresetn = NotRst
 PORT Slowest_sync_clk = CLK
 PORT MB_Debug_Sys_Rst = Debug_Rst
END